Kia Carens: Automatic Transaxle System / Specifications
Kia Carens RP (2013-2018) Service Manual / Automatic Transaxle System / Specifications
| Specifications |
|
Item |
Specification |
|
|
Transaxle model |
A6GF1 |
|
|
Engine model |
Gasoline 1.6 GDI |
|
|
Torque converter type |
3-element, 1-stage, 2-phase type |
|
|
Torque converter size |
Ø225 mm (8.8583 in.) |
|
|
Oil pump type |
Parachoid |
|
|
*ATF |
Capacity |
7.3 L (1.93 U.S gal., 7.71 U.S.qt., 6.42 Imp.qt.) |
|
Recommended |
- ATF SP-Ⅳ ·Recommended transaxle fluid : SK ATF SP-IV, MICHANG ATF SP-IV, NOCA ATF SP-Ⅳ |
|
|
Gear ratio |
1st |
4.400 |
|
2nd |
2.726 |
|
|
3rd |
1.834 |
|
|
4th |
1.392 |
|
|
5th |
1.000 |
|
|
6th |
0.774 |
|
|
Reverse |
3.440 |
|
|
Final gear ratio |
3.957 |
|
|
Component elements |
Oil filter |
1 unit |
|
Clutch |
2 units |
|
|
One-way clutch |
1 unit |
|
|
Brake |
3 units |
|
|
Planetary gear |
3 units |
|
|
Fluid pressure balance piston |
2 units |
|
|
Accumulator |
4 units |
|
|
Solenoid valve |
8 units (*VFS: 6, ON/OFF: 2) |
|
VFS: Variable Force Solenoid
Sensors
Input Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
|
Operation condition (°C)°F |
((-)40 ~ 150)) -40 ~ 302 |
|
|
Air gap(mm)in. |
(0.95 ~ 1.55) 0.0374 ~ 0.0610 |
|
|
Output voltage(V) |
High |
1.18 ~ 1.68 |
|
Low |
0.59 ~ 0.84 |
|
Output Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
|
Operation condition (°C)°F |
((-)40 ~ 150)) -40 ~ 302 |
|
|
Air gap(mm)in. |
(0.8 ~ 1.25) 0.0315 ~ 0.0492 |
|
|
Output voltage |
High |
1.18 ~ 1.68 |
|
Low |
0.59 ~ 0.84 |
|
Oil Temperature Sensor
▷ Type: Negative thermal coefficient type
▷ Specifications
|
Temp.[(°C)°F] |
Resistance (kΩ) |
|
(-40)-40 |
48.1 |
|
(-20)-4.0 |
15.6 |
|
(0)32.0 |
5.88 |
|
(20)68.0 |
2.51 |
|
(40)104.0 |
1.11 |
|
(60)140.0 |
0.61 |
|
(80)176.0 |
0.32 |
|
(100)212.0 |
0.18 |
|
(120)248.0 |
0.10 |
|
(140)284.0 |
0.06 |
|
(150)302.0 |
0.03 |
Inhibitor Switch
▷ Type: Combination of output signals from 4 terminals
▷ Specifications
|
Power supply (V) |
12 |
|
Output type |
Combination of output signals |
Solenoid Valves
Direct control VFS[26/B, T/CON]
▷ Control type : Normal low type
|
Control Pressure kpa (kgf/cm², psi) |
9.81 ~ 500.14 (0.1 ~ 5.1, 1.42 ~ 72.54) |
|
Current value(mA) |
50 ~ 850 |
| Internal
resistance(Ω) |
5.1 |
Direct control VFS[UD/B, OD/C, 35R/C]
▷ Control Type : Normal high type
|
Control Pressure kpa (kgf/cm², psi) |
500.14 ~ 9.81 (5.1 ~ 0.1, 72.54 ~ 1.42) |
|
Current value(mA) |
50 ~ 850 |
| Internal
resistance(Ω) |
5.1 |
Line Pressure Control VFS
▷ Control type : Normal high type
|
Control Pressure kpa (kgf/cm², psi) |
500.14 ~ 9.81 (5.1 ~ 0.1, 72.54 ~ 1.42) |
|
Current value(mA) |
50 ~ 850 |
| Internal
resistance(Ω) |
5.1 |
ON/OFF Solenoid Valve(SS-A, SS-B)
▷ Control type : Normal low type
|
Control pressure kpa (kgf/cm², psi) |
490.33(5.0, 71.12) |
| Internal
resistance(Ω) |
10 ~ 11 |
Solenoid Valve Operation Table
|
|
SS-A |
SS-B |
UD/B-VFS |
OD/C-VFS |
35R/C-VFS |
26/B-VFS |
|
N/H |
N/H |
N/H |
N/L |
|||
|
N, P |
● |
|
● |
|
● |
|
|
1 |
Δ |
|
|
Δ |
● |
|
|
2 |
|
|
|
● |
● |
● |
|
3 |
|
● |
|
● |
|
|
|
4 |
|
|
|
|
● |
|
|
5 |
|
● |
● |
|
|
|
|
6 |
|
|
● |
|
● |
● |
|
L |
● |
|
|
|
● |
|
|
R |
● |
● |
● |
|
|
|
● : Operation status
Δ : Connected at vehicle speed above 8km/h
Clutch & Brake Operation Table
|
|
Clutch |
Brake |
||||
|
OD/C |
35R/C |
OWC |
LR/B |
UD/B |
26/B |
|
|
N, P |
|
|
|
● |
|
|
|
1 |
|
|
● |
° |
● |
|
|
2 |
|
|
|
|
● |
● |
|
3 |
|
● |
|
|
● |
|
|
4 |
● |
|
|
|
● |
|
|
5 |
● |
● |
|
|
|
|
|
6 |
● |
|
|
|
|
● |
|
L |
|
|
|
● |
|
|
|
R |
|
● |
|
● |
|
|
●: Operation status
°: Operated at vehicle speed below 5km/h
Tightening Torques
|
Item |
N.m
|
kgf .m |
lb-ft
|
|
TCM mounting nut |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Shift cable bracket mounting bolt |
14.7 ~ 21.6 |
1.5 ~ 2.2 |
10.8 ~ 15.9 |
|
Input shaft speed sensor mounting bolt |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Output shaft speed sensor mounting bolt |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Shift lever assembly bolt |
8.8 ~ 13.7 |
0.9 ~ 1.4 |
9.4 ~ 10.8 |
|
Inhibitor switch mounting bolt |
9.8 ~ 11.8 |
1.0 ~ 1.2 |
7.2 ~ 8.7 |
|
Valve body cover mounting bolt |
11.8 ~ 13.7 |
1.2 ~ 1.4 |
8.7 ~ 10.1 |
|
Oil drain plug |
38.2 ~ 48.1 |
3.9 ~ 4.9 |
28.2 ~ 35.4 |
|
Torque converter mounting bolt |
45.1 ~ 52.0 |
4.6 ~ 5.3 |
33.3 ~ 38.3 |
|
Starter mounting bolt |
49.0 ~ 63.7 |
5.0 ~ 6.5 |
36.2 ~ 47.0 |
|
Automatic transaxle upper mounting bolt (TM=>Eng) |
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39.8 |
|
Automatic transaxle lower mounting bolt (Eng=>TM) |
42.2 ~ 48.1 |
4.3 ~ 4.9 |
31.1 ~ 35.4 |
|
42.2 ~ 53.9 |
4.3 ~ 5.5 |
31.1 ~ 39.8 |
|
|
Automatic transaxle support bracket mounting bolt |
58.9 ~ 78.5 |
6.0 ~ 8.0 |
43.4 ~ 57.8 |
|
Automatic transaxle mounting bracket bolt |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
Special service tools
Special Service Tools
Tool Name / Number
Illustration
Description
Engine support fixture (bar)
09200-3N000
...
Other information:
Kia Carens RP (2013-2018) Owners Manual: Air bag inflation conditions
Front air bags Front air bags are designed to inflate in a frontal collision depending on the intensity, speed or angles of impact of the front collision. Side and curtain air bags Side and/or curtain air bags are designed to inflate when an impact is detected by side collision sensors depending ...
Kia Carens RP (2013-2018) Owners Manual: Rear window wiper blade
1. Raise the wiper arm and pull out the wiper blade assembly. 2. Install the new blade assembly by inserting the center part into the slot in the wiper arm until it clicks into place. 3. Make sure the blade assembly is installed firmly by trying to pull it slightly. To prevent damage to the wiper ...
Copyright © www.kicaman.com 2015-2023
